Found in 2008, We are professional industrial valves manufacturers on wellhead control.

24 hours at your service: admin@sgvalves.com

Points for attention when purchasing valves

by:Sino Valves     2021-02-26
The following are some points of attention summarized when purchasing valves, which are only provided to manufacturers in need for reference and reference.   1. Variable speed transmission:   1. The material of the box and the internal and external anti-corrosion requirements are consistent with the valve body principle.  2. The box body should have sealing measures, and the box body can withstand 3 meters of water column immersion after assembly.  3. For the opening and closing limit device on the box, its adjusting nut should be inside the box.  4. The design of the transmission structure is reasonable. It can only drive the valve shaft to rotate when opening and closing, without causing it to move up and down, and the transmission components will bite properly and will not cause separation and slippage when opening and closing with load.  5. The seal of the variable speed transmission box and the valve shaft cannot be connected as a leak-free whole.   6. There is no debris in the box, and the gear bite part should be protected by grease.   2. Valve material:    1. Valve material: As gray cast iron pipes are gradually not recommended, the valve body material should be ductile iron, and the grade and actual physical and chemical testing data of the casting should be indicated.  2. Stem material: Strive for stainless steel stem (2CR13). Large diameter valves should also be stainless steel embedded stems.  3. Nut material: use cast aluminum brass or cast aluminum bronze, and the hardness and strength are greater than the valve stem.   4. Valve stem bushing material: its hardness and strength should not be greater than that of the valve stem, and it will not form electrochemical corrosion with the valve stem and valve body under water immersion. 5. Material of sealing surface:   ①Different valve types, different sealing methods and material requirements;   ②Common wedge gate valve, copper ring material, fixing method, and grinding method should all be explained;   ③Soft sealing gate valve, valve plate lining rubber Material physical and chemical and sanitary test data;   ④Butterfly valves should indicate the sealing surface material on the valve body and the sealing surface material on the butterfly plate; their physical and chemical test data, especially the hygienic requirements, anti-aging performance, and wear resistance of rubber; usually Adopt nitrile rubber and EPDM rubber, etc. It is strictly forbidden to mix with reclaimed rubber. 6. Valve shaft packing:   ①Because the valves in the pipe network are usually opened and closed infrequently, the packing is required to be inactive for several years, the packing does not age, and the sealing effect is maintained for a long time;   ②The valve shaft packing should also be subjected to frequent openings. When closed, the sealing effect is good;   ③In view of the above requirements, the valve shaft packing shall not be replaced for life or more than ten years; ④If the packing needs to be replaced, the valve design should consider measures that can be replaced under water pressure.  3. General requirements:   1. Valve specifications and categories should meet the requirements of the pipeline design documents.  2. The valve model should be marked with the national standard number requirements. If it is a corporate standard, the relevant description of the model should be indicated. 3. The working pressure of the valve requires the working pressure of the pipeline. Under the premise of not affecting the price, the working pressure that the valve can withstand should be greater than the actual working pressure of the pipeline; any side of the valve should be able to withstand 1.1 times the valve when it is closed. Working pressure value without leakage; when the valve is open, the valve body should be able to withstand twice the valve working pressure.  4. The valve manufacturing standard should state the national standard number on which it is based. If it is a corporate standard, the purchase contract should include corporate documents.   Fourth, the operating mechanism of the valve:    1. When the valve is operated, the opening and closing direction should be closed clockwise.  2. Because the valves in the pipe network are often opened and closed manually, the number of opening and closing revolutions should not be too much, even for large-diameter valves, it should be within 200-600 revolutions. 3. In order to facilitate the opening and closing operation of one person, the maximum opening and closing torque should be 240m-m.   under the pressure of the pipeline. 4. The opening and closing operation end of the valve should be a square tenon, and the size should be standardized, and it should face the ground for people It can be operated directly from the ground. Valves with roulette are not suitable for underground pipe networks. 5. Display panel of valve opening and closing degree ① The scale line of valve opening and closing degree should be cast on the cover of the gearbox or on the shell of the display panel after changing the direction, all face to the ground, and the scale line should be brushed with phosphor to show eye-catching  ②The material of the indicator disc needle can be made of stainless steel under the condition of good management, otherwise it is painted steel plate, and do not use aluminum skin;   ③The indicator disc needle is eye-catching and securely fixed. Rivet lock.  6. u200bu200bIf the valve is buried deeply, and the operating mechanism and the display panel are 15m away from the ground, they should be equipped with extension rod facilities and fixed firmly so that people can observe and operate from the ground. In other words, the opening and closing operations of valves in the pipe network are not suitable for downhole operations. V. Valve performance testing:    1. When a valve is manufactured in batches of a certain specification, an authoritative organization should be entrusted to perform the following performance testing:   ①The opening and closing torque of the valve under working pressure;   ②Under working pressure, the valve can be guaranteed Close the number of continuous opening and closing times;   ③The detection of the flow resistance coefficient of the valve in the pipeline water condition. 2. The valve should undergo the following tests before leaving the factory:   ①When the valve is open, the valve body should withstand the internal pressure of twice the valve working pressure;   ②When the valve is closed, both sides bear 11 times the valve working pressure. Value, no leakage; but the leakage value of the metal-sealed butterfly valve is not greater than the relevant requirements.  
There is a strong need for more research on , in order to be able to provide strong and conclusive evidence of their industrial valves china effects. However, recent studies have provided valuable insights into how the intake of may result in improved industrial valves china.
Do you want industrial valves china Contact Us? We also have industrial valves china. visit Sino Global Industrial Valves to know more.
Millions of women across the world suffer from industrial valves china. Are you also one of them who suffer from acne problem? now you will see some hope in Sino Global Pipeline Construction Equipment Limited's offer of . Click Sino Global Industrial Valves to know more.
The above are only part of the examples regarding Contact Us, for more information, please click here Sino Global Industrial Valves.
Producing with varied technical skills, Contact Us can be used in a wide range of applications as industrial valves china.
Custom message
Chat Online
Chat Online
Chat Online inputting...